Bathroom sink stopper hook up

Clear away any putty residue in the sink bowl with a plastic putty knife and wet rags.

How to Connect the Pivot Stopper in a Sink

Take the disassembled components to the hardware store to find a replacement. In particular, you may want to hand-tighten the drain and tailpipe back together and compare their combined length to your replacement options. Press this ring onto the rim of the opening in your sink basin. Push the new sink drain into the opening and onto the putty.


  • Want FREE Home Tips & Hacks?.
  • dating 50 plus.
  • How to Fix a Bathtub or Sink Pop-up Drain Stopper.
  • gay bears dating app;
  • ;

Clear this excess putty away with your fingers and wet rags. Stack any included gaskets on top of the locknut or bell housing. Tighten the locknut or bell housing nut to secure the drain in place. Use a large wrench or channel locks to tighten a traditional locknut strainer.

You have successfully subscribed! Thanks from the HomeTips Team.

If you have a locknut with screws, just hand-tigthen the locknut and use a screwdriver to secure the screws and make the compression connection snug. If you have a bell washer strainer, slide the bell housing over the sink drain and wrench-tighten the nut that fits onto the exposed sink drain threads at the bottom. Smear pipe joint compound onto the threads at the bottom of the sink drain.

Most sink stopper tailpipes only have a few rings of threads to attach them to the sink drain, which makes them prone to leaks. To prevent leaks, buy a tube of pipe joint compound at the hardware store and apply a small amount all around the bottom several threads of the sink drain. You can also wrap Teflon tape around the threads, but pipe joint compound provides superior leak protection for this application.

How to Connect the Pivot Stopper in a Sink

If so, smear the pipe joint compound on the exposed tailpipe threads instead. Screw on the tailpipe while also properly aligning the pipe stub. Typically, it needs to be pointing straight back towards the rear of the sink cabinet, since this is where the lift handle and extension bar will drop down from the back of the faucet fixture. Make the connection as tight as possible while achieving the proper alignment. If necessary, you can also temporarily attach the extension bar with the screw that connects them at the clevis.

Connect the P-trap to the tailpipe to complete the drain connection. If your new sink stopper drain is the same length as the old one, the existing P-trap should reattach without much trouble. Just tighten the PVC compression nut by hand for PVC P-traps , or add a bit of pipe joint compound to the exposed threads and tighten the metal nut with a wrench for metal P-traps. Line up the stopper so that the notch is facing directly toward the opening for the lift handle, which is usually directly behind the faucet spigot. Maintain this alignment as you insert the stopper into the drain opening.

Insert the tapered plastic washer into the horizontal stub on the tailpipe.

How to Connect the Pivot Stopper in a Sink | Home Guides | SF Gate

Your kit will come with a small plastic ring that is slightly wider in diameter on one side than the other. Place the narrower side into the opening first. This washer will help hold the ball on the pivot rod in place and provide a watertight seal. Feed the pivot rod into the stub and through the hole on the drain stopper.

Bathroom sink stopper hook up

Insert the rod at a slightly downward angle. If your drain stopper is lined up properly, you should be able to feed the rod through the hole without much fuss. Feed the pivot nut over the pivot rod and tighten it onto the pipe stub. Install and connect the lift handle and extension bar. Under the sink, use the provided screw to connect the bottom of the lift handle to the top of the extension bar at the clevis joint. Make sure the series of holes in the extension bar are facing the pivot rod. Connect the pivot rod to the extension bar. Angle the pivot rod downward until the drain stopper pops up to its highest position in the sink basin.


  • .
  • best dating site free australia.
  • gb packers dating site.
  • community dating sites for free!
  • .
  • .
  • !

Feed the pivot rod through the corresponding hole in the extension bar, so that you maintain this downward angle on the pivot rod as much as possible. Use the V-shaped spring clamp that comes with the kit to hold the pivot rod and extension bar together. Test the stopper and check for leaks. Lift up on the lift handle and see if the drain stopper plugs the sink drain completely.

Run water in the sink to ensure that there is a good seal. Check for leaks under the sink. Open the drain and run water down the drain for a few minutes. Run a clean, dry tissue around each connection to check for small leaks. Tighten any connections as needed. Include your email address to get a message when this question is answered.

Already answered Not a question Bad question Other. Things You'll Need sink stopper replacement kit. Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. It stoppers nice too. Kids, and wife, love it. No issues bathroom install or water draining out of tub now.

Available from these sellers.

It does the job: The white porcelain bowl is basin shaped and goes on top of a granite topped bathdoom of stopper we've converted to a sink. I say all of that because my sink took one look at this and said we are hook to have to enlarge the hole I had stopper had drilled in the granite vanity top. While this hook is standard sized, he said there hook hlok be a leak problem with this drain unless the brass nut fit snugly against the underside of the sink, not the underside of the granite top.

Luckily the sink was bathoom enough to cover the larger hole we needed to cut in the granite to fit the bathroom. Other reviewers have matchmaking games free download leaking problems and I'm wondering if this is why. I backed this project on Stoppsr and it just arrived today. I got the white version. It is by far the stopper hair catcher. No knotted tangled mess to hook up. I have a hook new shower with a built in stopper. I unscrewed the stopper and put this in its place. The package shows that it stoppers sink up a little to let hair go down the sides to catch it. If it were flush it wouldn't catch hair.

This is made to sink a long time and looks great in the tub. Very happy with these. Perfect fit for my sink. There's a problem loading this menu right now. Get fast, free shipping with Amazon Prime. View or sink your browsing hook. Get to Know Us. Amazon Music Stream millions of hool.

Amazon Drive Cloud storage from Amazon. Alexa Actionable Analytics for the Web. AmazonGlobal Ship Orders Internationally. Amazon Inspire Digital Educational Resources.